PMC Products

Home

Vendors

Products

PMC Products

Barracuda-PMC+: (from BittWare, Inc.)
BittWare´s Barracuda-PMC+ (BCPM) board is a high-speed analog input board that provides data capture for two 14-bit, up to 105 MHz A/D channels and streams the data directly to a Xilinx Virtex-II FPGA, which provides A/D control and data distribution and front-end processing capabilities. A 64-bit, 66 MHz PCI interface and four SHARC link ports make the captured data available to the host board, and a bank of up to 512 MB of SDRAM is available for snapshot acquisitions.

Hammerhead-PMC: (from BittWare, Inc.)
The Hammerhead-PMC+ (HHPM) packs the processing power of four ADSP-21160 SHARCŽ DSPs and the speed of a 64-bit, 66 MHz PCI interface onto a single-width PMC module. You can use the Hammerhead-PMC+ to add I/O or additional processors and memory on any standard PMC or PMC+ capable carrier board. The board also features 64-256 MB of SDRAM for general-purpose code and data storage and a 2MB bank of FLASH memory.

MM-7110: (from VMETRO)
The MM-7110 can transform PowerPC and x86 Single Board Computers, AltiVec DSP boards, A/D converters, graphic engines or any carrier with a PMC site into a signal processing engine. The primary bus that interfaces to the host system is located in the MM-7110´s LX200 FPGA. This PCI/PCI-X bus provides a data transfer, communication and control plane to the rest of the system.

* Utilizes the largest Xilinx Virtex-4 LX and Virtex-4 SX FPGAs
* Most FPGA Logic resources and DSP resources ever to be offered on a PMC form factor
* Optional CoSine FPGA IP and Development Kit provide totally preconfigured, fully tested infrastructure for rapid development time
* Virtex-4 LX200 CoSine Primary Device
* Virtex-4 SX55 CoSine Companion Device
* 512MB or 1GB DDR II memory with ECC
* PCI/PCI-X bus interface that operates in 32-bit or 64-bit PCI mode @ 66MHz or 64-bit PCI-X mode @ 66MHz or 133MHz
* Inter-FPGA interconnect supports over 3 GB/s of full-duplex bandwidth
* Device Drivers available for Linux, VxWorks, and Windows
* Rugged Air Cooled and Conduction Cooled versions

PMC-7852/G: (from Adlink Technology Inc.)
Features :
- PCI Bus:32-bit/33 MHz
- V(I/O):3.3 V or 5 V Universal V(I/O)
- Transfer Speed:6 Mbps (default) up to 12 Mbps
- Max. Communications Distance:200 meters for each port under 6 Mbps
- Max. Controllable Points:2016 input and 2016 outputs
- Transfer Mode:Half/Full Duplex
- I/O Scan Time:About 1ms for scanning 1000 points(6 Mbps)
- Connector:RJ-45 phone jack connector

More Info

PMC-FPGA05: (from VMETRO)
The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support

PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: BittWare´s Barracuda-PMC+ (BCPM) board is a high-speed analog input board that provides data capture for two 14-bit, up to 105 MHz A/D channels and streams the data directly to a Xilinx Virtex-II FPGA, which provides A/D control and data distribution and front-end processing capabilities. A 64-bit, 66 MHz PCI interface and four SHARC link ports make the captured data available to the host board, and a bank of up to 512 MB of SDRAM is available for snapshot acquisitions.
Hammerhead-PMC: (from BittWare, Inc.)
The Hammerhead-PMC+ (HHPM) packs the processing power of four ADSP-21160 SHARCŽ DSPs and the speed of a 64-bit, 66 MHz PCI interface onto a single-width PMC module. You can use the Hammerhead-PMC+ to add I/O or additional processors and memory on any standard PMC or PMC+ capable carrier board. The board also features 64-256 MB of SDRAM for general-purpose code and data storage and a 2MB bank of FLASH memory.

MM-7110: (from VMETRO)
The MM-7110 can transform PowerPC and x86 Single Board Computers, AltiVec DSP boards, A/D converters, graphic engines or any carrier with a PMC site into a signal processing engine. The primary bus that interfaces to the host system is located in the MM-7110´s LX200 FPGA. This PCI/PCI-X bus provides a data transfer, communication and control plane to the rest of the system.

* Utilizes the largest Xilinx Virtex-4 LX and Virtex-4 SX FPGAs
* Most FPGA Logic resources and DSP resources ever to be offered on a PMC form factor
* Optional CoSine FPGA IP and Development Kit provide totally preconfigured, fully tested infrastructure for rapid development time
* Virtex-4 LX200 CoSine Primary Device
* Virtex-4 SX55 CoSine Companion Device
* 512MB or 1GB DDR II memory with ECC
* PCI/PCI-X bus interface that operates in 32-bit or 64-bit PCI mode @ 66MHz or 64-bit PCI-X mode @ 66MHz or 133MHz
* Inter-FPGA interconnect supports over 3 GB/s of full-duplex bandwidth
* Device Drivers available for Linux, VxWorks, and Windows
* Rugged Air Cooled and Conduction Cooled versions

PMC-7852/G: (from Adlink Technology Inc.)
Features :
- PCI Bus:32-bit/33 MHz
- V(I/O):3.3 V or 5 V Universal V(I/O)
- Transfer Speed:6 Mbps (default) up to 12 Mbps
- Max. Communications Distance:200 meters for each port under 6 Mbps
- Max. Controllable Points:2016 input and 2016 outputs
- Transfer Mode:Half/Full Duplex
- I/O Scan Time:About 1ms for scanning 1000 points(6 Mbps)
- Connector:RJ-45 phone jack connector

More Info

PMC-FPGA05: (from VMETRO)
The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support

PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: The Hammerhead-PMC+ (HHPM) packs the processing power of four ADSP-21160 SHARCŽ DSPs and the speed of a 64-bit, 66 MHz PCI interface onto a single-width PMC module. You can use the Hammerhead-PMC+ to add I/O or additional processors and memory on any standard PMC or PMC+ capable carrier board. The board also features 64-256 MB of SDRAM for general-purpose code and data storage and a 2MB bank of FLASH memory.
MM-7110: (from VMETRO)
The MM-7110 can transform PowerPC and x86 Single Board Computers, AltiVec DSP boards, A/D converters, graphic engines or any carrier with a PMC site into a signal processing engine. The primary bus that interfaces to the host system is located in the MM-7110´s LX200 FPGA. This PCI/PCI-X bus provides a data transfer, communication and control plane to the rest of the system.

* Utilizes the largest Xilinx Virtex-4 LX and Virtex-4 SX FPGAs
* Most FPGA Logic resources and DSP resources ever to be offered on a PMC form factor
* Optional CoSine FPGA IP and Development Kit provide totally preconfigured, fully tested infrastructure for rapid development time
* Virtex-4 LX200 CoSine Primary Device
* Virtex-4 SX55 CoSine Companion Device
* 512MB or 1GB DDR II memory with ECC
* PCI/PCI-X bus interface that operates in 32-bit or 64-bit PCI mode @ 66MHz or 64-bit PCI-X mode @ 66MHz or 133MHz
* Inter-FPGA interconnect supports over 3 GB/s of full-duplex bandwidth
* Device Drivers available for Linux, VxWorks, and Windows
* Rugged Air Cooled and Conduction Cooled versions

PMC-7852/G: (from Adlink Technology Inc.)
Features :
- PCI Bus:32-bit/33 MHz
- V(I/O):3.3 V or 5 V Universal V(I/O)
- Transfer Speed:6 Mbps (default) up to 12 Mbps
- Max. Communications Distance:200 meters for each port under 6 Mbps
- Max. Controllable Points:2016 input and 2016 outputs
- Transfer Mode:Half/Full Duplex
- I/O Scan Time:About 1ms for scanning 1000 points(6 Mbps)
- Connector:RJ-45 phone jack connector

More Info

PMC-FPGA05: (from VMETRO)
The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support

PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: The MM-7110 can transform PowerPC and x86 Single Board Computers, AltiVec DSP boards, A/D converters, graphic engines or any carrier with a PMC site into a signal processing engine. The primary bus that interfaces to the host system is located in the MM-7110´s LX200 FPGA. This PCI/PCI-X bus provides a data transfer, communication and control plane to the rest of the system.

* Utilizes the largest Xilinx Virtex-4 LX and Virtex-4 SX FPGAs
* Most FPGA Logic resources and DSP resources ever to be offered on a PMC form factor
* Optional CoSine FPGA IP and Development Kit provide totally preconfigured, fully tested infrastructure for rapid development time
* Virtex-4 LX200 CoSine Primary Device
* Virtex-4 SX55 CoSine Companion Device
* 512MB or 1GB DDR II memory with ECC
* PCI/PCI-X bus interface that operates in 32-bit or 64-bit PCI mode @ 66MHz or 64-bit PCI-X mode @ 66MHz or 133MHz
* Inter-FPGA interconnect supports over 3 GB/s of full-duplex bandwidth
* Device Drivers available for Linux, VxWorks, and Windows
* Rugged Air Cooled and Conduction Cooled versions
PMC-7852/G: (from Adlink Technology Inc.)
Features :
- PCI Bus:32-bit/33 MHz
- V(I/O):3.3 V or 5 V Universal V(I/O)
- Transfer Speed:6 Mbps (default) up to 12 Mbps
- Max. Communications Distance:200 meters for each port under 6 Mbps
- Max. Controllable Points:2016 input and 2016 outputs
- Transfer Mode:Half/Full Duplex
- I/O Scan Time:About 1ms for scanning 1000 points(6 Mbps)
- Connector:RJ-45 phone jack connector

More Info

PMC-FPGA05: (from VMETRO)
The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support

PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: Features :
- PCI Bus:32-bit/33 MHz
- V(I/O):3.3 V or 5 V Universal V(I/O)
- Transfer Speed:6 Mbps (default) up to 12 Mbps
- Max. Communications Distance:200 meters for each port under 6 Mbps
- Max. Controllable Points:2016 input and 2016 outputs
- Transfer Mode:Half/Full Duplex
- I/O Scan Time:About 1ms for scanning 1000 points(6 Mbps)
- Connector:RJ-45 phone jack connector

More Info
PMC-FPGA05: (from VMETRO)
The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support

PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: The PMC-FPGA05 is a Xilinx Virtex-5 LX110 FPGA based board with high speed, customizable data I/O. The powerful FPGA is boosted by multiple banks of memory to ensure that processing capabilities of the PMC-FPAGA05 is maximized.

* Xilinx Virtex-5 LX110 FPGA
* Multiple banks of SRAM for DSP
* Multiple banks of SDRAM for large buffers
* PCI-X interface
* Customizable digital I/O
* Windows, VxWorks and Linux support
PMC260 - Ultra2 SCSI PMC controller: (from Kontron AG)
Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148

Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: Features:
- Ultra2 SCSI I/O processor
- Up to 80 MByte/s transfer rate Wide LVD SCSI-bus
- Up to 15 SCSI peripherals, up to 12m cable
- Supports SCSI-1, -2, -3, Ultra and Ultra2
- Bus-master DMA (FIFO onboard)
- 32-bit PMC module
- Extended temperature range -40°C to +85°C

Description:
Improved data transfer rates, parallel data integrity, up to 12m SCSI-cable lengths and easy system configuration for up to 15 peripherals are just some of the benefits provided by this Ultra2 SCSI PMC module from Kontron.

http://www.kontron-emea.com/index.php?id=226&cat=167&productid=148
Reef-PMC+: (from BittWare, Inc.)
BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.

Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: BittWare´s Reef-PMC+ (RFPM) is a reconfigurable FPGA board combining the power of the XILINX Virtex-II FPGA and the Analog Devices ADSP-21160 SHARCŽ DSP. Configurable for nearly any application, the RFPM allows system designers to take advantage of both the flexibility of a reconfigurable FPGA and the processing power of a general-purpose DSP. The Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. And the ADSP-21160 DSP provides additional I/O and processing power for the board. Rounding out the RFPM´s feature set are a 64/66 PCI interface, a 64-512 MB bank of SDRAM, and 2 MB of Flash memory.
Remora-PMC+: (from BittWare, Inc.)
Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.

T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: Reconfigurable FPGA card. BittWare´s Remora-PMC+ (RMPM) is a reconfigurable FPGA board featuring the power of the XILINX Virtex-II FPGA. A PCI Mezzanine Card (PMC) providing BittWare´s PMC+ I/O extensions, the RMPM allows system designers to add the flexibility of a reconfigurable FPGA to their PMC or PMC+ compatible host boards. Configurable for nearly any application, the Virtex-II features up to 1 million system gates, a flexible digital I/O interface, and reconfigurable computing blocks. Rounding out the RMPM´s feature set are a 64/66 PCI interface and a 64-512 MB bank of SDRAM.
T2-PMC: (from BittWare, Inc.)
BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.

Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: BittWare´s T2-PMC (T2PM) DSP board features the ADSP-TS201 TigerSHARC processor from Analog Devices. To take full advantage of this high-performance DSP, this multiprocessor PCI Mezzanine Card (PMC) implements BittWare's ATLANTiS framework, which combines robust TigerSHARC processing with the versatile Virtex-II Pro FPGA from Xilinx to offer ultra high performance and unprecedented I/O bandwidth.
Technobox 4933 -- PMC-to-PCI Adapter: (from Technobox, Inc.)
Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.

Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: Adapts a single-wide PMC to a standard PCI board for desktop PCs. This passive adapter is ideal for use as a delivery vehicle for PMCs in a PCI environment. Its simple, economical design does not include LEDs, clamping diodes, logic analyzer test headers and test features found on other, more comprehensive Technobox PMC development tools.
Tetra-PMC+: (from BittWare, Inc.)
BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.

V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: BittWare´s Tetra-PMC+ (TRPM) board is a high-speed analog input board that provides data capture for four 14-bit A/D channels running at up to 105 MHz. The board streams the data directly to an Altera Cyclone II FPGA, which provides A/D control, data distribution, and front-end processing capabilities. A 32-bit, 66 MHz PCI interface and four TigerSHARC link ports make the captured data available to the host board.
V10x0 10GbE Mezzanine Module: (from AdvancedIO Systems, Inc.)
AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.: AdvancedIO's V10x0 family of Mezzanine modules is the industry´s first 10GbE configurable solution for data communication in full production. Utilizing Xilinx FPGAs, the V10x0 family includes processing modules that perform critical system functions, such as:
Deep packet inspection UDP Acceleration Up/Down Conversion Encryption/Decryption FFT
The V10x0 family offers extreme scalability for applications requiring 10GbE, such as: SIGINT, Radar / Sonar, EW, MILCOM and Wireless Infrastructure.
AdvancedIO also works with customers to achieve solutions that meet their packet processing requirements, and offers consultation for FPGA application development AdvancedIO is partnered with lead system providers and also offers total system solutions.